Home > Countertop Dishwashers · Compatibility

Will a Countertop Dishwasher Fit Under Your Cabinets? Heights and Plate Sizes by Model

Specs checked November 16, 2026|Countertop Dishwashers · Compatibility

Under-cabinet heightPlate sizeMeasuring guide

Here is the trap, stated plainly: the gap between a kitchen countertop and the wall cabinets above it is about 18 inches in most US kitchens. Countertop dishwashers stand 17.2 to 18.2 inches tall. And their manufacturers require 19.6 to 20.1 inches of clearance to actually install and use them.

All three numbers are true at once — which is why "it fits" and "it works" are different questions, and why this category generates so many returns. A machine can slide into the gap and still be unusable, because you can't open the fill lid, can't get the funnel in, or can't tilt a plate through the door.

This guide compares the published heights, required clearances, and plate limits model by model, then gives you the four measurements to take before any of them matter.

In this article:

Disclosure: This site may earn a commission from links on this page, at no extra cost to you. All specifications below are manufacturer-published figures, checked on November 16, 2026. We do not claim hands-on test results we don't have.

The short answer

  • Compare your counter-to-cabinet gap against the manufacturer's required clearance, not the machine's height. COMFEE' requires more than 19.6" for a machine 17.24" tall; Hermitlux requires 19.88" for one 18.03" tall.
  • The extra ~2 inches buy room for the top-fill tank opening and funnel on tank models — the subject of our tank vs faucet comparison.
  • Plate limits run from 9.5" (COMFEE') to 12" (Farberware) — and the big numbers assume the plate is loaded at an angle.
  • If your gap is under ~19.5", plan on an open counter section or a cart instead of the under-cabinet spot.

Why required clearance is bigger than the machine

On a tank model, water goes in through the top. The lid or funnel needs vertical room to open and pour — Hermitlux's manual for the HMX-DW03 states the total height with the funnel at 50.5 cm (19.88"), against a body height of 45.8 cm (18.03"). That difference, roughly two inches, is the clearance the manufacturers bake into their requirements.

Faucet-only models don't fill from the top, but they still aren't pure body height: doors, racks, and the simple act of loading a tall glass argue for margin. The safe rule covers both types:

Your gap must beat the manufacturer's required clearance figure — not the height in the product title.

Heights, clearances, and plate sizes by model

ModelWater supplyDimensions (W × D × H)Required clearanceMax plate diameterPlace settings
COMFEE' CDC17P0AWB Tank (5L) + faucet option 16.53" × 17.13" × 17.24" More than 19.6" 9.5" 30+ pieces (manufacturer listing)
Farberware FDW05ASBWHA Tank (5L) + faucet option 16.5" × 17.3" × 17.3" Not stated as a single figure in the manual — allow funnel room above the fill opening 12" (at an angle) Not stated in the manual
Hermitlux HMX-TDJ04 Tank (5L) + faucet option 16.85" × 16.73" × 18.03" At least 19.88" 10.25" (at an angle) 4
Hermitlux HDW5CW01 Tank (5L) + faucet option 16.85" × 16.73" × 18.23" At least 20.08" 10.25" (at an angle) 5
Danby DDW621WDB Faucet only 21.65" × 19.69" × 17.24" No top-fill requirement; allow loading margin above the door About 10.5" 6

Sources: manufacturer manuals and published specifications (COMFEE' CDC17P0AWB listing and manual; Farberware FDW05ASBWHA user manual; Hermitlux HMX-TDJ04 and HDW5CW01 manuals; Danby DDW621WDB published specs). Checked November 16, 2026. Note the width story: the Danby trades a wide, low body (21.65") for its 6 place settings, while the tank models stay narrow and go taller.

Two readings of this table matter most:

Don't forget width and depth

Height gets the attention because cabinets impose it, but the other two dimensions quietly eliminate models too. The Danby needs a 21.65"-wide spot — wider than many apartment counters offer in one unbroken run — and at 19.69" deep it leaves little counter in front of it on a standard-depth counter once the door is open. The tank models invert the problem: narrow footprints around 16.5–16.9" wide, but taller bodies. Measure the spot in all three dimensions, and remember the machine also needs a few inches behind or beside it for hoses — a unit pushed flush against the backsplash with its drain hose kinked behind it has not really "fit."

What "fits 12-inch plates" actually means

Read the manuals closely and a qualifier appears again and again: plates fit "loaded at an angle." Hermitlux says it of its 10.25" limit; Farberware's manual says large items up to 12" can be placed at an angle. A tilted plate's vertical footprint is smaller than its diameter — that's the entire trick.

Practical consequences:

[AFFILIATE LINK: Farberware countertop dishwasher] / [AFFILIATE LINK: Hermitlux countertop dishwasher] — placeholder: product links are added after Amazon Associates approval.

Measure first: the four numbers

  1. Counter-to-cabinet gap. Tape measure from the countertop surface to the underside of the wall cabinet, at the exact spot — and check for under-cabinet lights or rails that hang lower than the cabinet bottom.
  2. Counter depth and door swing. These machines are 16.7–19.7" deep, and the door opens down toward you. You need the body on the counter plus comfortable loading room in front of it.
  3. Your largest plate's diameter. Compare it against the model's stated limit, remembering the at-an-angle qualifier.
  4. Drain and outlet reach. The drain hose still has to reach the sink or a bucket (both supply types — see the tank vs faucet guide), and the cord has to reach an outlet without crossing the sink.

Fit checklist

  • Gap ≥ the manufacturer's required clearance (19.6–20.1" for the tank models above), not just ≥ body height
  • No under-cabinet light, rail, or trim intruding into that gap
  • Counter depth fits the body, with loading room in front
  • Largest plate ≤ the stated max diameter — with the angle caveat accepted
  • Drain hose reaches its target; outlet reachable
  • Counter can carry the machine plus a full tank of water (these units weigh roughly 26–46 lb dry, before water and dishes)

When the gap is too small

An ~18" gap rules out the under-cabinet spot for tank models, but it doesn't rule out the category:

FAQ

What is the standard clearance between a countertop and upper cabinets?

About 18 inches in most US kitchens — which is exactly the problem: tank-model dishwashers need 19.6–20.1" per their manuals. Always measure your own kitchen; older and custom kitchens vary in both directions.

Why does a 17.24-inch machine need 19.6 inches of clearance?

Because of everything above the body: on tank models, the fill lid and funnel. COMFEE' states the requirement directly — the distance between countertop and wall cupboard must be more than 19.6" — even though the machine itself is 17.24" tall. The requirement, not the height, is the number to shop by.

Can a countertop dishwasher fit 12-inch plates?

One in this comparison can: Farberware's manual allows items up to 12 inches, placed at an angle. Most others top out at 9.5–10.5 inches. If your everyday plates are oversized, this single spec may decide your model for you.

Does a taller machine hold more?

Not reliably. The tallest model here (Hermitlux HDW5CW01, 18.23") is rated at 5 place settings; the widest (Danby, 17.24" tall but 21.65" wide) holds 6. Capacity follows interior volume and rack design in all three dimensions — compare place settings and plate limits, not height.

What if my plates are 11 inches?

Then COMFEE' (9.5") and Hermitlux (10.25") are out, and you're choosing between the Farberware (12" at an angle) and living with angled loading — or measuring whether your 11" plates are really 11", since many "11-inch" plates measure closer to 10.5". Measure the plate, then decide.

The bottom line

  • Shop by required clearance, not height: 19.6–20.1" for tank models, against a typical ~18" kitchen gap
  • The hidden ~2 inches are the top-fill opening and funnel — the price of the tank's faucet independence
  • Plate limits: 9.5" to 12" by model, always at an angle; measure your largest plate
  • Too-small gap ≠ no dishwasher: open counter, cart, or the low-and-wide faucet format are the honest alternatives

Height is the second decision. The first is how the machine gets water at all — if you haven't settled that, the tank vs faucet comparison is the place to start. And if your faucet is part of the plan, check its thread before anything else with our adapter guide.

Specifications on this page come from manufacturer-published documents (COMFEE', Farberware, and Hermitlux manuals and product documentation; Danby DDW621WDB published specifications), last checked November 16, 2026. Dimensions and requirements vary by model revision; confirm the figures for your exact model before buying.

Keep reading

▸ Countertop Dishwasher: Built-In Water Tank vs Faucet Hookup — the first decision, compared spec by spec.

▸ Portable Washer Faucet Adapter Doesn't Fit? — if the faucet is in your plan, its thread decides whether the plan works.